Hurd Swinging Patio Door Sweep and Seal Comparison

To Order Hurd Replacement Parts Click Here

For Hurd Swinging Patio doors over the years Hurd used a variety of sweep sand seals for their door. This is a comparison to help you identify which seal or sweep you need for your vintage of door. This comparison and be very helpful if the sweep or seal you need is missing.

Hurd Door Sweep and Seals

 

Order Hurd Parts Click Here

543 – Patio Door Panel Guide Kit Install Instructions

How To Install  543 – Patio Door Panel Guide Kit -Guide Buttons

Order # 543 Here At R&R Windows & Door Authorized Hurd Parts Dealer

Install Patio door guide buttons on the inside of the operating door 1″ from each side on the panel and flush with the top of the sash panel as seen in diagram. It is necessary for the screw to set squarely in the guide button for it to be secure in the sash panel.

How To Install Hurd Patio Door Guide Buttons

How To Install Hurd Patio Door Guide Buttons

Order # 543 Here At R&R Windows & Door Authorized Hurd Parts Dealer

How To Replace a Casement Operator

Updated! This how to video will teach you how to replace a casement operator on a casement window. The window used in this video is the Hurd Energy Saver Casement with Truth Casement hardware – Now Called Sierra Pacific WI product.To order Hurd Replacement Parts visit http://www.Hurd-Parts.com to order other window and door part brands visit http://www.WindowPartsCenter.com 

 

How To: Remove a casement sash from frame

Quick How To video on removing a Hurd Casement Sash from a frame in a few easy steps.

If you are replacing the operator on a Casement there is no need to disconnect whole sash from the frame. Just disconnect the operator arms from the sash bracket and/or track shoe from the sash as shown in the 1st part of the video. No need to disconnect the top and bottom hinge. Note that in this video this is a new style window and parts have the SNAP RINGS on the Hinges and sash bracket. Older style windows and parts will have a sliver or black clip that moves to detach from the sash

This video we are working on a Hurd Energy Saver casement window / Sierra Pacific WI Energy Saver –  with Truth Encore operator and Truth adjustable hinges

To buy Hurd replacement parts visit our online store at www.Hurd-Parts.com

 

Install Balance on Hurd Energy Saver Double Hung Windows from 08/16/2010 to Present

As of August 6, 2014- Sierra Pacific Industries (SPI) purchase of Hurd and Superseal Windows and Doors. As of 8/2/2016 the Energy Saver line is still the same Hurd Energy Saver line but is now called Wisconsin Energy Saver Product.

Directions & Photos provided by Hurd Windows & Doors

To order Hurd and Sierra Pacific Wisconsin Product Parts

Visit R&R Windows & Doors Website

www.RandRwindow.com

1. Open bottom sash, tilt in and to the side to remove

Photo 1

Hurd Energy Saver Double Hung

Open bottom sash, tilt in and to the side to remove

2. Open top sash, tilt in and to the side to remove.
3. Remove screen.
4. Starting with the bottom cover, CAREFULLY remove the metal
cover by inserting a putty knife screwdriver at the end of the
cover, gently pry up and remove. Repeat steps with wood
jamb liner above PHOTO 2 & 3

Photo 2

Hurd Energy Saver Double Hung

Starting with the bottom cover, CAREFULLY remove the metal
cover by inserting a putty knife screwdriver at the end of the
cover

Photo 3

 Hurd Energy Saver Double Hung

gently pry up and remove. Repeat steps with wood
jamb liner above PHOTO 2 & 3

5. Move to the bottom of the jambliner, squeeze the liner to release it from the jamb, PHOTO 4, 5, 6 & 7.

Photo 4

Hurd Energy Saver Double Hung

Move to the bottom of the jambliner, squeeze the liner to release it from the jamb

Photo 5

 Hurd Energy Saver Double Hung

Move to the bottom of the jambliner, squeeze the liner to release it from the jamb,

Photo 6

 Hurd Energy Saver Double Hung

Move to the bottom of the jambliner, squeeze the liner to release it from the jamb,

Photo 7

 Hurd Energy Saver Double Hung

Move to the bottom of the jambliner, squeeze the liner to release it from the jamb,

6. Unlock the balance by inserting a flat head screwdriver tip into the balance shoe. The balance is under tension so hold onto the lock until it disengages. PHOTO 8 A & B

Photo 8 A

 Hurd Energy Saver Double Hung

Unlock the balance by inserting a flat head screwdriver tip into the balance shoe. The balance is under tension so hold onto the lock until it disengages.

Photo 8 B

 Hurd Energy Saver Double Hung

Unlock the balance by inserting a flat head screwdriver tip into the balance shoe. The balance is under tension  so hold onto the lock until it disengages.

7. Slide old balance out and insert new balance. Make sure it hooks on the top of the liner. PHOTO 9

Photo 9

 Hurd Energy Saver Double Hung

7. Slide old balance out and insert new balance. Make sure it hooks on the top of the liner.

8. Install new jambliners. Starting at the top of the jamb, slide the liner into the space at head as shown in PHOTO 10. Make sure the liner fits snugly up against the head of the frame.

Photo 10

 Hurd Energy Saver Double Hung

8. Install new jambliners. Starting at the top of the jamb, slide the liner into the space at head as shown in PHOTO 10. Make sure the liner fits snugly up against the head of the frame.

9. Using a flat blade putty knife, place the blade on top of the sill gasket and slide the bottom of the jambliner into place PHOTO 11 & 12. Making sure the jambliner is fit tightly along the full length of the side jamb.

Photo 11

 Hurd Energy Saver Double Hung

9. Using a flat blade putty knife, place the blade on top of the sill gasket and slide the bottom of the jambliner into place PHOTO 11 & 12. Making sure the jambliner is fit tightly along the full length of the side jamb.

Photo 12

 Hurd Energy Saver Double Hung

9. Using a flat blade putty knife, place the blade on top of the sill gasket and slide the bottom of the jambliner into place PHOTO 11 & 12. Making sure the jambliner is fit tightly along the full length of the side jamb.

9. Starting with the bottom cover, place at the bottom of the jambliner and seat the cover firmly into place PHOTO 13 & 14 .

Photo 13

 Hurd Energy Saver Double Hung

9. Starting with the bottom cover, place at the bottom of the jambliner and seat the cover firmly into place PHOTO 13 & 14 .

Photo 14

 Hurd Energy Saver Double Hung

9. Starting with the bottom cover, place at the bottom of the jambliner and seat the cover firmly into place PHOTO 13 & 14 .

10. Re-install the wood jambliner covers.
Starting at the top PHOTO 15, slide the cover up into the space at the head of the frame and seat the
cover into place along the jambliner.

Photo 15

 Hurd Energy Saver Double Hung

10. Re-install the wood jambliner covers.
Starting at the top PHOTO 15, slide the cover up into the space at the head of the frame and seat the
cover into place along the jambliner.

Make sure the dust block is to the outside of the liner as shown in PHOTO 16.

Photo 16

 Hurd Energy Saver Double Hung

Make sure the dust block is to the outside of the liner as shown in PHOTO 16.

11. Prepare balance for the sash installation. Insert a
flat head screwdriver tip into the balance shoe,
PHOTO 17, sliding shoe downward stopping 12″
from the sill. Lock the balance shoe in place making
sure the lock shoe hub is in the open position.

Photo 17

 Hurd Energy Saver Double Hung

11. Prepare balance for the sash installation. Insert a
flat head screwdriver tip into the balance shoe,
PHOTO 17, sliding shoe downward stopping 12″
from the sill. Lock the balance shoe in place making
sure the lock shoe hub is in the open position.

12. Locate top sash, which includes latch pins
on top rail. With clad side up and sash pins
furthest away, hold the sash horizontally,
tiliting sideways to a 30° angle allowing the
pins to pass to the outer track. Insert one
pin into the locked balance shoe, PHOTO 18.
Lower the sash to a full horizontal position
inserting the opposite side pin into the
balance shoe.
Depress tilt pins and push sash to a full
vertical position, advancing sash to the outer
tracks. Release tilt pins.
Repeat for the bottom sash inserting sash pins
into the inner tracks.

Photo 18

 Hurd Energy Saver Double Hung

12. Locate top sash, which includes latch pins
on top rail. With clad side up and sash pins
furthest away, hold the sash horizontally,
tiliting sideways to a 30° angle allowing the
pins to pass to the outer track. Insert one
pin into the locked balance shoe, PHOTO 18.
Lower the sash to a full horizontal position
inserting the opposite side pin into the
balance shoe.
Depress tilt pins and push sash to a full
vertical position, advancing sash to the outer
tracks. Release tilt pins.
Repeat for the bottom sash inserting sash pins
into the inner tracks.

13. Check operation & locking functions
Depress tilt pins and push sash to a full vertical
position, PHOTO 19, advancing sash to the outer
tracks. Release tilt pins.Repeat for bottom sash inserting
sash pins into the inner tracks.

Photo 19

 Hurd Energy Saver Double Hung

13. Check operation & locking functions
Depress tilt pins and push sash to a full vertical
position, PHOTO 19, advancing sash to the outer
tracks. Release tilt pins.Repeat for bottom sash inserting
sash pins into the inner tracks.

To order Hurd and Sierra Pacific Wisconsin Product Parts

Visit R&R Windows & Doors Website

www.RandRwindow.com

#837 – Adjustable Oak Threshold How To Replace & Adjust

INSTRUCTIONS FOR P#837

To order #837 click on link http://www.randrwindow.com/adoakth.html

To remove old threshold:

 

Use a #3 Philips bit on your drill – to unscrew the screws on the top of the old oak threshold all the way. Once screws are completely removed the old threshold will pull up.

 

There are T nuts in a T track underneath the threshold that the screws screw into.

 

You can reuse the old T nuts or replace the T nuts in the T track with the new T nuts provided with the new threshold

 

To replace the T nuts – you will remove the old T nuts by sliding them out of the track – there should be a space at one of the ends of the track for you to do this.

 

Take new T nuts and slide them into the track through the same space at one of the ends of the T track.

 

Replace with new threshold by aligning the T nuts to the screws in the threshold.

 

Screw in all screws into the T nuts below – be careful not to over tighten – and the screws are used to adjust the threshold as well.

 

Adjusting the Threshold:

 

Once the threshold is installed and all screws are screwed into the T nuts – the threshold can be adjusted by tightening or loosening the screws.

 

Tightening screws to lower the threshold or loosening the screws to it rise up.

 

To Order Click On Link Adjustable Oak Threshold

How To Replace Old Style Handle Set With C Elite Handle Set #522

To Order # 522 click on link: http://www.randrwindow.com/handle-c-elite-complete-kit.html

 

If you want to use C Elite Handle package to replace P/N 516 Upgrade Door Handle. Additional parts will be needed!You will need a new recessed mortise lock with the gray/sliver cylinder part# 518. You will also need the New Style Shim part #512-NEW or else the handle set will be loose. You will have to fill the top screw hole that will be left over from the old handle set. You can do this by using part number 546 or 546U binding post.Please read all details below and watch video below.

Part # 518 Mortise Lock with Gray/Sliver Cylinder Sold Separately – $40.00 each

If your Recessed Mortise Lock has the black cylinder you will need to purchase a new recessed mortise lock with the gray/sliver cylinder for this handle set to work.

Part # 512-NEW New Style Shim For C Elite handle set. Comes in white only as shown in video below. No additional cost when purchased with the C Elite Handle Set.

Part # 546 Standard Binding Post Screw – Silver Mill Finish – No additional cost when purchased with the C Elite Handle Set. No other finishes available. Will work in existing upper hole in Hurd door- no modification needed.

Part# 546U UPGRADE Binding Post Screw – Chrome, Brass Dull Finish, Dark Bronze & 18-8 Stainless Steel $16 each. 1/4″ Diameter. ***NOTE*** When using the Upgrade # 546U Binding post. The diamieter is 1/4″ so you will have to drill out the hole with a 5/16″ drill bit for these binding post to fit.

To Order #522 click on link: http://www.randrwindow.com/handle-c-elite-complete-kit.html

How To Replace Broken Screen Corners

Here is a helpful step by step directions on how to replace screen corners on a Hurd Window Screen.

To order screen corners go to www.RandRwindow.com

Part # 141 for old style screen corner and Part # 140 for new style screen corner. Comes in: Gold tone, White or bronze.

PIcture of New style Screen Corner

PIcture of New style Screen Corner

Old Style Screen Corner

Old Style Screen Corner

Part # 998 for Screen Spline Tool

 998 a
For these instructions old screen corners (Part # 141) has been used. But the instructions apply also to the New Style Screen Corners ( Part Number # 140). To Order: www.RandRwindow.com
1. The Screen Corner – you are only going to remove 2 screen corners at a time so you do not have to rescreen your whole screen
 Clipboard01
2. With a pointed object pull up the spline. The spline is located around the screen frame
 Clipboard17
3. If you cannot locate the edge of the spline or if it is not near a corner you will have to cut it with a knife
 Clipboard18
4. Gently pull spline and remove from the top part of the screen. Do not remove spline completely!
 Clipboard19
5. Notice how spline is only removed from the top and only a few inches down on both sides of the screen
 Clipboard20
6. Gently pull down screen mesh to the spline
 Clipboard21
7. Remove top part of frame by pulling straight up. Now 2 screen corners should be exposed
Clipboard22
8. Remove broken screen corner and replace with new screen corner on both sides. If part of the old screen corner is broke off in the screen frame – use a pair of pliers to pull it out. If it won’t come out shove the broken part more into the screen frame so the new screen corner can fit all the way in.
 Clipboard23
9. Make sure you put in the new screen corner the same way as the old one. Repeat on other side
 Clipboard24
10. Put top frame with new screen coners back into side frame
 Clipboard25
11. Push top and side frame together so they are tight against the screen corner
Clipboard26
12. Push screen mesh back into frame groove
 Clipboard27
13. Using spline tool (Part # 998) push in spline back into the screen frame
 Clipboard28
14. The spline may stretch when you push it back into the groove. If this happens cut off any excess
 Clipboard29
15.  Finish inserting spline with spline tool. Repeat steps to replace the bottom 2 screen corners.
  Clipboard30
Helpful tip: If one screen corner is broke then most likely the opposite diagonal screen comer is broke or at least cracked and should also be replaced.