How To Replace Old Style Handle Set With C Elite Handle Set #522

To Order # 522 click on link: http://www.randrwindow.com/handle-c-elite-complete-kit.html

 

If you want to use C Elite Handle package to replace P/N 516 Upgrade Door Handle. Additional parts will be needed!You will need a new recessed mortise lock with the gray/sliver cylinder part# 518. You will also need the New Style Shim part #512-NEW or else the handle set will be loose. You will have to fill the top screw hole that will be left over from the old handle set. You can do this by using part number 546 or 546U binding post.Please read all details below and watch video below.

Part # 518 Mortise Lock with Gray/Sliver Cylinder Sold Separately – $40.00 each

If your Recessed Mortise Lock has the black cylinder you will need to purchase a new recessed mortise lock with the gray/sliver cylinder for this handle set to work.

Part # 512-NEW New Style Shim For C Elite handle set. Comes in white only as shown in video below. No additional cost when purchased with the C Elite Handle Set.

Part # 546 Standard Binding Post Screw – Silver Mill Finish – No additional cost when purchased with the C Elite Handle Set. No other finishes available. Will work in existing upper hole in Hurd door- no modification needed.

Part# 546U UPGRADE Binding Post Screw – Chrome, Brass Dull Finish, Dark Bronze & 18-8 Stainless Steel $16 each. 1/4″ Diameter. ***NOTE*** When using the Upgrade # 546U Binding post. The diamieter is 1/4″ so you will have to drill out the hole with a 5/16″ drill bit for these binding post to fit.

To Order #522 click on link: http://www.randrwindow.com/handle-c-elite-complete-kit.html

815 / 816 Door Hinge Adjustment Instructions

Vertical And Horizontal Adjustment For 815 and 816 Hinge.

Each hinge has both a Vertical and Horizontal adjustment. Hinges are Handed Left Hand & Right Hand. Click on links below to order.

To determine handing: Match up your existing hinge to picture on website.

Link: Order Left Hand Hinge # 815

Link: Order Right Hand Hinge # 816

815-816

815-Adjustment

 

Step 1: Before you adjust the hinges. You need to remove the weight of the door panel off of the hinges. By having someone lifting the door panel up and/or shimming below the door panel to keep weight off hinges as you adjust them – follow instructions below on how to Lower or  Raise and Adjust Horizontally.

Step 2: Once you make an adjustment let the weight of the door panel back onto hinges by letting go of the panel or remove any shimming so weight of panel is back onto the hinges. Operate panel to see if more adjustment is needed. If you need to adjust again you will have to repeat step 1 above.

To Lower Door:

  1. Turn “V” screw on top and middle hinges counter clockwise until its stops
  2. Now slowly turn “V” screw on bottom hinge, counter clockwise to lower door to desired position. Close door and check for alignment.
  3. When door is properly aligned turn “V” screw on top and middle hinge clockwise until its snug. Aprox. same position as “V” screw on bottom hinge.
  4. Adjustment Complete

To Raise Door:

  1. Turn “V” screw clockwise on bottom hinge until door raises to desired position. Close door and check alignment.
  2. Now turn “V” screw clockwise on top and middle hinge until screw is snug. Approx. same position as screw on bottom hinge.
  3. Adjustment Complete

To Adjust Door Horizontally:

Turning the “H” screw clockwise will move the door away from the hinged jamb

Turning the “H” screw counter clockwise will move the door closer to the hinged jamb.

All three hinges may require adjustment to achieve proper horizontal alignment.

If door keeps falling out of alignment new hinges are needed. Click on link below to order.

Link: Order Left Hand Hinge # 815

Link: Order Right Hand Hinge # 816

www.RandRwindow.com

 

Hurd Sliding Patio Door Stadard Oak Handle Set 1993 – 2006

This article will show you how to: change the handing and install the standard oak handle set and use the keeper finder used on Hurd sliding patio doors from 1993 – 2006

To order a new Standard Oak Handel Set go to www.RandRwindow.com P/N 508
To order Hurd Sliding Screen Door Keeper only go to www.RandRwindow.com P/N 533

508

Installation and Handing Instructions:

Tools required: Philips Screwdriver

Determine handing direction from exploded view below (XO or OX)

Clipboard01

On the back side of the inside handle there is an “E” shaped guide locating the actuator lever. The actuator should be moved to one end. Align with the hub of the lock as shown in the detail.

Place the inside handle against door while inserting actuator into vertical slotted hub of mortise lock. Install two 8-32 x 2 1/2″* length screw for clad door provided through the inside handle to attach outside pull (and plastic shim on clad door). DO NOT USE POWER DRIVERS TO INSTALL HANDLE SCREWS!

To install Keeper Plate follow directions below.

Optional key cylinder: cut the tail piece to 3/4″ length.

*2 3/8″ length screw for wood exterior door

Keeper Installation Instructions:

Install hardware as shown above

Before installing the Keeper Plate hold the Keeper Locator Template in place against the mortise lock.

Clipboard01

Close the door firmly, allowing the keeper locator template to make the location for the keeper screws in the side jamb.

Clipboard01

Install the keeper with two #8 x 1 1/4″ screws and adjust to the proper height.

Adjust mortise lock hoot using a common paint screwdriver until the hook is properly extended. Close door. Lock door and check for excessive play. Readjust the hook until the door will lock snug.

To order a new Standard Oak Handel Set go to www.RandRwindow.com P/N 508
To order Hurd Sliding Screen Door Keeper only go to www.RandRwindow.com P/N 533